Mobile locksmithPensacola to Panama City Estimate agreed before work starts Typically there in 15–20 min Open 24/7 (850) 920-7113 Text us
Illustration: an opened key fob with its coin battery and a small screwdriver

Key fob battery replacement: how do you change it?

(850) 920-7113

A key fob battery is a coin cell you can usually change yourself in a few minutes. Match the size printed on the old battery first.

THE SHORT ANSWER

A fob that stops answering usually just has a tired battery. Changing it takes a small screwdriver or a coin, and a minute of care with the case.

QUICK ANSWER

To change a key fob battery, open the case at the seam, note which side faces up and fit the same coin cell. If the buttons still fail or the car will not start, call (850) 920-7113 with the make and model.

Published: · Updated: · By the Best Value Locksmith team

Do you need to reprogram a key fob after changing the battery?

Most key fobs don't need reprogramming after a battery change. The pairing is stored in the fob and the car, not in the battery. Swap the cell within a few minutes, and don't press the buttons while it's out. Some makes need a short resync, such as locking and unlocking with the key in the ignition. Check the owner's manual for those steps. If the buttons still do nothing with a fresh battery seated correctly, look for corrosion on the contacts and a protective sticker on the new cell. A fob that unlocks the doors but won't start a push-to-start car usually has a separate problem with its chip or the car's antenna. That needs a programming tool, not another battery.

STEP 01

Find the right battery

The size is printed on the old cell, such as CR2032 or CR2025, and in the owner's manual. Buy the same size and voltage. A thinner cell can rattle loose, and a thicker one can crack the case.

STEP 02

Open the case without breaking it

Many fobs have a hidden mechanical key that releases the shell, plus a slot at the seam for a coin or flat screwdriver. Twist gently along the seam instead of prying at one point. Keep the rubber button pad and any small gasket in place while you work.

STEP 03

Put it back together and test

Fit the new cell with the same side up as the old one, then close the case until it clicks all the way around. Test lock, unlock, and the trunk from a few steps away. On a push-to-start car, start the engine too.

STEP 04

When it is not the battery

If a fresh battery changes nothing, the fob may have lost its pairing, water or a drop may have damaged the circuit board, or the car may need the fob programmed again. You'll need the make, model, and year. Most newer cars also need a programming tool.

Was this guide helpful?

GOOD QUESTIONS. STRAIGHT ANSWERS.

More questions about key fob battery

Can’t find your answer? Call or text and tell us what’s going on.

Most car key fobs are water-resistant at best, not waterproof. A splash is usually fine, but a swim or the washing machine can kill one, and salt water is worse, which matters near the beach. Take the battery out, dry everything fully and fit a fresh cell. If the fob still fails, it needs replacing and programming.

Yes, in most cars. A push-to-start car can usually still start if you hold the fob against the button or the marked spot, because its chip needs no battery power, and the engine keeps running once started. You may see a warning on the dash. Replace the coin cell before your next trip, usually without reprogramming.

The fob may be fine, but a dead car battery means the car cannot respond, so remote unlock and push-button start will not work. Use the mechanical key hidden in the fob to open the door, then jump-start or replace the car battery. If the fob still fails afterward, check its own battery next.

A key fob battery that keeps dying usually points to a poor or wrong-size cell, a stuck button, moisture in the case, or a proximity fob stored close to the car, where it keeps talking to the vehicle. Store it away from the car, fit a fresh cell, and replace the fob if the drain continues.

The range shrinks first: the fob only works close to the car, or you press a button twice. Some cars show a key battery warning on the dash. On push-to-start cars a weak fob can still start the engine when held against the start button or a marked spot on the column, which the manual shows. Replace the cell before it dies completely. If a new one does not help, call (850) 920-7113.

Usually yes. Most fobs open at the seam with a coin or a small flat screwdriver, sometimes after you slide out the hidden mechanical key. Use the same coin cell size, keep the same side facing up and press the case closed evenly. Work over a table so small parts do not disappear. If the case is glued or cracked, or the fob still fails after the swap, call (850) 920-7113 with the make and model.

Check that the cell sits flat, the right side is up and no protective sticker is left on it. Clean the contacts if they look dull or green. If the buttons still do nothing, the fob may have lost its pairing or been damaged, and some cars need it programmed again with a tool. Note whether the car still starts, since that points to the fix. Call (850) 920-7113 to talk it through.
A SOLUTION STARTS WITH A CONVERSATION

Need a hand with a lock or key?

Call (850) 920-7113 and tell us what happened and where you are. We confirm availability and the estimate before any work begins.

Call now(850) 920-7113Text